LCD Toshiba 37X3030D

Servisní část určená pro profesionály

Moderátor: Moderátoři

Zpráva
Autor
Uživatelský avatar
ZdenekHQ
Významný člen
Příspěvky: 25519
Registrován: 21 črc 2006, 00:00
Bydliště: skoro Brno
Kontaktovat uživatele:

#16 Příspěvek od ZdenekHQ »

Opět slepá cesta. Ten měnič je zablokovanej, jinak je OK.

Jsem v háji, potřeboval bych diagnostickej kabel a soft, ten procesor žije, jen se nebaví se zbytkem TV.

Ještě si budu chvíli hrát, ale tady moje schopnosti končí, kupovat naslepo nový desky nebudu.
Pro moje oslovení klidně použijte jméno Zdeněk
Správně navržené zapojení je jako recept na dobré jídlo.
Můžete vynechat půlku ingrediencí, nebo přidat jiné,
ale jste si jistí, že vám to bude chutnat[?
]
Uživatelský avatar
jezevec
Hlavní moderátor
Příspěvky: 6101
Registrován: 13 čer 2004, 00:00
Bydliště: Břeclavsko
Kontaktovat uživatele:

#17 Příspěvek od jezevec »

Pokud bys měl cestu někde poblíž, tak se stav, mrknu na to.
Uživatelský avatar
ZdenekHQ
Významný člen
Příspěvky: 25519
Registrován: 21 črc 2006, 00:00
Bydliště: skoro Brno
Kontaktovat uživatele:

#18 Příspěvek od ZdenekHQ »

Potřeboval bych půjčit desku s FLI8548. To je totiž jedinej obvod, se kterým to komunikuje, dál to nejde.
Přílohy
fli.jpg
(235.26 KiB) Staženo 125 x
Pro moje oslovení klidně použijte jméno Zdeněk
Správně navržené zapojení je jako recept na dobré jídlo.
Můžete vynechat půlku ingrediencí, nebo přidat jiné,
ale jste si jistí, že vám to bude chutnat[?
]
Uživatelský avatar
yesper26
Příspěvky: 1052
Registrován: 19 kvě 2012, 00:00
Bydliště: Bratislava

#19 Příspěvek od yesper26 »

A ked dam invertor na ex. zdroj, svietia ti trubice, podsvietenie panelu ? Tcon este nemusi byt vadny, ja som mal vadny jeden smd trandik, tiez som sa s tym sral cely den, prisiel som na to tak ze som meral napetia na smd, len tak ma to napadlo, no a na jednom som mal na jednej nohe 7V, na druhej tiez daco a na kolektore, na tej vrchnej nic, tak som chytil vylupol trandik von a prepojil som zrejme emitor tych 7V s kolektorom, zapol telku a obraz naskocil :D
Uživatelský avatar
ZdenekHQ
Významný člen
Příspěvky: 25519
Registrován: 21 črc 2006, 00:00
Bydliště: skoro Brno
Kontaktovat uživatele:

#20 Příspěvek od ZdenekHQ »

Ano, invertor funguje, trubice svítí.

S Tcon to vůbec nekomunikuje, ani mu to nesepne napájení, stejně jako to nesepne invertor.
Pro moje oslovení klidně použijte jméno Zdeněk
Správně navržené zapojení je jako recept na dobré jídlo.
Můžete vynechat půlku ingrediencí, nebo přidat jiné,
ale jste si jistí, že vám to bude chutnat[?
]
Uživatelský avatar
yesper26
Příspěvky: 1052
Registrován: 19 kvě 2012, 00:00
Bydliště: Bratislava

#21 Příspěvek od yesper26 »

Tak chyt a zopni invertor a t-con natvrdo. T-con ak vies ako ho zopnut.
Uživatelský avatar
ZdenekHQ
Významný člen
Příspěvky: 25519
Registrován: 21 črc 2006, 00:00
Bydliště: skoro Brno
Kontaktovat uživatele:

#22 Příspěvek od ZdenekHQ »

K čemu to bude ? Procesor může zjistit, že TCON (či invertor) je vadný jedině tehdy, když se s ním pokusí komunikovat. Pokud se o to vůbec nepokusí, je chyba jinde.
Pro moje oslovení klidně použijte jméno Zdeněk
Správně navržené zapojení je jako recept na dobré jídlo.
Můžete vynechat půlku ingrediencí, nebo přidat jiné,
ale jste si jistí, že vám to bude chutnat[?
]
Uživatelský avatar
ZdenekHQ
Významný člen
Příspěvky: 25519
Registrován: 21 črc 2006, 00:00
Bydliště: skoro Brno
Kontaktovat uživatele:

#23 Příspěvek od ZdenekHQ »

yesper26 píše:Tak chyt a zopni invertor a t-con natvrdo. T-con ak vies ako ho zopnut.


Byla chvilka času, tak jsem to zkusil - žádná změna.
Pro moje oslovení klidně použijte jméno Zdeněk
Správně navržené zapojení je jako recept na dobré jídlo.
Můžete vynechat půlku ingrediencí, nebo přidat jiné,
ale jste si jistí, že vám to bude chutnat[?
]
Uživatelský avatar
Habesan
Příspěvky: 7377
Registrován: 12 led 2009, 00:00
Bydliště: Plzeňsko
Kontaktovat uživatele:

#24 Příspěvek od Habesan »

Dává ti to možnost dostat T-Con do režimu zkušebních obrazců, abys viděl, jestli je v pořádku alespoň panel a jestli má smysl v opravě pokračovat.

Některé procesory mají jeden analogový výstup pro DVB-T příjem na SCART, na kterém během Flashování běží průběh v procentech, ale neposílá se v tu dobu na SCART.
Viděl jsem i mrtvější telky. Dokonce takové, které během Flashování tenhle výstup neaktivovaly, ale když jsem je po uplynutí delší doby restartoval, tak bylo všechno v pořádku.
Některé telky měly paralelně k Flash pozici pro neosazený mnohapinový konektor, kterým by se dala v případě nouze přečíst/přepsat natvrdo, ale nikdy jsem ten konektor nedostal do ruky.

Docela mě děsí to 416 kuličkové PBGA:
Genesis FLI8548H
SGS-Thomson FLI8548H
Sháním hasičák s CO2 "sněhový", raději funkční.
(Nemusí mít platnou revizi.)
(Celkově budu raději, když se to obejde bez papírů.)
Uživatelský avatar
ZdenekHQ
Významný člen
Příspěvky: 25519
Registrován: 21 črc 2006, 00:00
Bydliště: skoro Brno
Kontaktovat uživatele:

#25 Příspěvek od ZdenekHQ »

Tak jsem kontaktoval autorizovaný servis Toshiba, co oni na to, sice byli vstřícní, ale je to pro ně historický model s ukončenou podporou, takže vyhodit.
Pro moje oslovení klidně použijte jméno Zdeněk
Správně navržené zapojení je jako recept na dobré jídlo.
Můžete vynechat půlku ingrediencí, nebo přidat jiné,
ale jste si jistí, že vám to bude chutnat[?
]
Uživatelský avatar
ZdenekHQ
Významný člen
Příspěvky: 25519
Registrován: 21 črc 2006, 00:00
Bydliště: skoro Brno
Kontaktovat uživatele:

#26 Příspěvek od ZdenekHQ »

Log ze systémovýho konektoru :

Kód: Vybrat vše

  Checking for PCMCIA update...

  No card detected.

Booting mtd-block

Kernel located @ BFC00000

zimage at BFC10014

zimage size 0008CE4F

Uncompressing Linux at load address 80040000

Booting linux kernel @ 80159000
 Please press Enter to activate this console. Version out of Filesystem for Image A: 2 9
Version out of Filesystem for Image B: 2 9
Stored for Image A: ff 2 9
Stored for Image B: a5 2 9
Preferred Image: 1  Boot Fail Count A: 4  Boot Fail Count B:   0
Version numbers for Image A differ - updating Flash information
Stored for Image A: a5 2 9
Image A is invalid marking it!


------------begin-of-log-------------

[    0.002] IN [  32]|audio_isr_bh(): woken up[a_dec 0] a_irq 0

[    0.002] IN [  32]|audio_isr_bh(): going to sleep[a_dec 0]

[    0.003] IN [  33]|audio_isr_bh(): woken up[a_dec 1] a_irq 0

[    0.003] IN [  33]|audio_isr_bh(): going to sleep[a_dec 1]

LNX_InitializeSystem() info:    System Initialize Start

Lnx_Open() debug:   open. device[/dev/tc90400int1]

Lnx_Open() debug:   open. device[/dev/tc90400int2]

Lnx_Open() debug:   open. device[/dev/tc90400int3]

Lnx_Open() debug:   open. device[/dev/tc90400int4]

Lnx_Open() debug:   open. device[/dev/tc90400int5]

lnx_mmap() info:    offset 0x00001000, size 0x01fff000, hint 0x40001000 =» map 0x40001000

lnx_mmap() info:    offset 0x17400000, size 0x00140000, hint 0x57400000 =» map 0x57400000

lnx_mmap() info:    offset 0x18000000, size 0x00090000, hint 0x58000000 =» map 0x58000000

lnx_mmap() info:    offset 0x180a0000, size 0x00020000, hint 0x580a0000 =» map 0x580a0000

lnx_mmap() info:    offset 0x180d0000, size 0x00330000, hint 0x580d0000 =» map 0x580d0000

lnx_mmap() info:    offset 0x1c004000, size 0x00001000, hint 0x5c004000 =» map 0x5c004000

lnx_mmap() info:    offset 0x1f100000, size 0x00010000, hint 0x5f100000 =» map 0x5f100000

lnx_mmap() info:    offset 0x1e01c000, size 0x00004000, hint 0x5e01c000 =» map 0x5e01c000

lnx_mmap() info:    offset 0x1e008000, size 0x00001000, hint 0x5e008000 =» map 0x5e008000

lnx_mmap() info:    offset 0x1e020000, size 0x00001000, hint 0x5e020000 =» map 0x5e020000

LNX_InitializeSystem() info:    System Initialize Start Done

0xa08b1000, 0x0018f000, TSPASP_FW

0xa0a40000, 0x00003000, IRISC_FW

0xa0a43000, 0x0000c000, WORK_AREA

0xa0a4f000, 0x00004000, COM_AREA

0xa0a53000, 0x00001000, AUDIO_WORK_AREA

0xa0a54000, 0x00134000, AUDIO_RES_AREA

0xa0bba000, 0x00020000, ASTD0

0xa0b88000, 0x00032000, AUDIO_DEC0

0xa0c1f000, 0x00080000, VSTD0

0xa0c9f000, 0x002f8000, VSTD1

0xa0c9f000, 0x002f8000, VBUF0

0xa0c9f000, 0x002f8000, VBUF1

0xa0c9f000, 0x002f8000, CAPTURE

0xa0c1e000, 0x00001000, VUSERBUF0

0xa0c9f000, 0x002f8000, VUSERBUF1

0xa0bda000, 0x0003c000, SECTIONS

0xa0c16000, 0x00008000, TPDATA

0xa0c9f000, 0x002f8000, RECORDING0

0xa0c9f000, 0x002f8000, RECORDING1

0xa0c9f000, 0x002f8000, PLAYBACK

0xa0f97000, 0x00065400, GFX_FB

0xa0ffd000, 0x00001000, GFX_SCALER

0xa0ffe000, 0x00001000, GFX_GFX_CLUT

0xa0fff000, 0x00001000, GFX_OSD_CLUT

0xa0c9f000, 0x002f8000, ASTD1

0xa0c9f000, 0x002f8000, AUDIO_DEC1

0xa0c9f000, 0x002f8000, ASTD2

0xa0c9f000, 0x002f8000, AUDIO_DEC2

0xa0c9f000, 0x002f8000, AUDIO_PCM0

0xa0c9f000, 0x002f8000, AUDIO_PCM1

0xa0c9f000, 0x002f8000, AUDIO_PCM2

0xa0c9f000, 0x002f8000, AUDIO_PCM3

__calc_memory_map(): mem 8820, lower map adr 8900

system_init(): debug 3, SD system

system_boot_MeP(): tspasp_fw @ 0xa08b1000

system_boot_MeP(): com_area  @ 0xa0a4f000

system_boot_MeP(): work_area @ 0xa0a43000

mutex object created. id[0] name[CmdFifoAccess]
mutex object created. id[1] name[TSPIntMaskRegAccess]
mutex object created. id[2] name[AMePIntMaskRegAccess]
mutex object created. id[3] name[STCIntMaskRegAccess]
mutex object created. id[4] name[TSPAudioStartStopRegAccess]
mutex object created. id[5] name[TSPASTDRunCh0RegAccess]
mutex object created. id[6] name[TSPASTDRunCh1RegAccess]
mutex object created. id[7] name[TSPASTDRunCh2RegAccess]
mutex object created. id[8] name[a0_mutex]
mutex object created. id[9] name[a1_mutex]
mutex object created. id[10] name[a2_mutex]
mutex object created. id[11] name[mxvd]
mutex object created. id[12] name[mxvs]
lock mutex timeout. errno[4] result[145] id[12] name[mxvs]
translate_vdev_error(): VDEV_DecodeStop(dec->eVideoCh): Mutex timeout [src/glue/src/glue_video.c:543 in glue_video_stop()]

lock mutex timeout. errno[4] result[145] id[12] name[mxvs]
translate_vdev_error(): VDEV_DecodeStop(dec->eVideoCh): Mutex timeout [src/glue/src/glue_video.c:543 in glue_video_stop()]

mutex object created. id[13] name[mi_mutex]
mutex object created. id[14] name[pf_mutex]
mutex object created. id[15] name[sf_mutex]
mutex object created. id[16] name[rf_mutex]
mutex object created. id[17] name[psf_mutex]
mutex object created. id[18] name[DemuxMutex]
system_init(): TSP-MeP-FW version: 0xbe215300
TSP-MeP-FW Demux-part version: 0x06122100
TSP-MeP-FW Video-part version: 0x07011600
TSP-MeP-FW DCXO-part version: 0x06031400

system_init(): IRISC-MEPG2-FW version: 0x00000000
IRISC-MPEG1-FW version: 0x00000000
IRISC-JPEG-FW version: 0x00000000
ASP-FW version: 0x07011700
AMP-FW version: 0x07011700

LNX_SetInterruptHandler() debug:   == set interrupt handler intno(0) ==

LNX_EnableInterrupt() debug:   GMBR interrupt enable.

LNX_SetInterruptHandler() debug:   == set interrupt handler intno(1) ==

LNX_EnableInterrupt() debug:   GFX  interrupt enable.

mutex object created. id[19] name[mxvd]
mutex object created. id[20] name[mxgd]
mutex object created. id[21] name[mxgs]
mutex object created. id[22] name[mxgm]
mutex object created. id[23] name[mxgb]
LNX_SetInterruptHandler() debug:   == set interrupt handler intno(2) ==

LNX_EnableInterrupt() debug:   VIOU interrupt enable .

LNX_SetInterruptHandler() debug:   == set interrupt handler intno(4) ==

LNX_EnableInterrupt() debug:   EXT1 interrupt enable .

mutex object created. id[24] name[TunerMutex]
mutex object created. id[25] name[TunerMutex]
[    2.783] MI [  30]|ICE_InitialiseSystemMemory(): not implemented

[    2.784] DE [  30]|ICE_DebugInit(): not implemented

[  30]|board_get_booted_image(): mtdblock 3, booted_image 1

[  30]|board_confirm_boot(): setting b bfc to 0

[  30]|write_store_value(): dest 7744, value 0x00, [0] 0x00, [1] 0xffffffff

[    2.787] DE [  30]|ICE_DebugInit(): not implemented

[    3.438] AU [  30]|ICE_AudioInit(): device_number 0

[    3.438] AU [  30]|ICE_AudioOpen(): device_number 0

[    3.442] ST [  30]|ICE_StcOpen(): [0]

[    3.478] CI [  30]|ICE_CIInit(): CI init

[    3.497] CI [  41]|ICE_CIResetAll(): Reset ALL Card

[    3.514] TP [  30]|ICE_TPDataInit():

[    3.514] TP [  30]|ICE_TPDataDeviceOpen(): [0x100579d0] device_type 0

[    3.519] TP [  30]|ICE_TPDataInit():

[    3.520] TP [  30]|ICE_TPDataDeviceOpen(): [0x100579d0] device_type 0

[  49]|board_get_booted_image(): mtdblock 3, booted_image 1

[    3.600] CI [  41]|ICE_CIOpen(): CI open slot:0

[    3.600] CI [  41]|ICE_CIOpen(): CI open slot:1

[  49]|read_version_information_from_flash(): image 1, major 2, minor 9

[  49]|board_get_image_version(): slot 1, valid 165, major 2, minor 9

[    3.609] BL [  49]|ICE_GetImageVersion(): image @ slot 1 ok, major 2, minor 9

[    3.610] SU [  49]|ICE_SoftwareVersion(): sw_ver 29

[  49]|read_version_information_from_flash(): image 0, major 2, minor 9

[  49]|board_get_image_version(): slot 0, valid 255, major 2, minor 9

[    3.631] BL [  49]|ICE_GetImageVersion(): image @ slot 0 invalid

[  49]|read_version_information_from_flash(): image 1, major 2, minor 9

[  49]|board_get_image_version(): slot 1, valid 165, major 2, minor 9

[    3.651] BL [  49]|ICE_GetImageVersion(): image @ slot 1 ok, major 2, minor 9
second slot version = 29

[  49]|read_store_value(): dest 7680, value 0x01

[  49]|board_get_preferred_image(): image 1

[    3.653] BL [  49]|ICE_GetBootSlot(): ICE_GetBootSlot 1

[  49]|read_version_information_from_flash(): image 0, major 2, minor 9

[  49]|board_get_image_version(): slot 0, valid 255, major 2, minor 9

[    3.674] BL [  49]|ICE_GetImageVersion(): image @ slot 0 invalid

[  49]|read_version_information_from_flash(): image 1, major 2, minor 9

[  49]|board_get_image_version(): slot 1, valid 165, major 2, minor 9

[    3.695] BL [  49]|ICE_GetImageVersion(): image @ slot 1 ok, major 2, minor 9
second slot version = 29

[    3.695] BL [  49]|ICE_SetBootSlot(): ICE_SetBootSlot 1

[  49]|board_update_preferred_image(): preferred_image 1

[  49]|write_store_value(): dest 7680, value 0x01, [0] 0x01, [1] 0xfffffffe

[    3.698] RE [  56]|board_receive_ir():

[    3.699] RE [  30]|ICE_RemoteRegisterKeypressFunction():

mutex object created. id[26] name[mxgd]
[  49]|board_get_fw_version(): now version : 2.2

[  49]|board_get_booted_image(): mtdblock 3, booted_image 1

[  49]|read_version_information_from_flash(): image 1, major 2, minor 9

[    4.443] IN [  49]|tee_stb_handler_audio_set_volume(): dec 0, phys_audio 0, level 1000

[    4.443] AU [  49]|ICE_AudioVolume(): device_number 0, precent_volume 100

[    4.557] RE [  49]|board_ir_set_repeat(): key 'ICE_keypress_volume_up'

[    4.558] RE [  49]|board_ir_set_repeat(): key 'ICE_keypress_volume_down'

[    4.558] RE [  49]|board_ir_set_repeat(): key 'ICE_keypress_program_up'

[    4.559] RE [  49]|board_ir_set_repeat(): key 'ICE_keypress_program_down'

[    5.054] IN [  49]|tee_stb_handler_audio_set_volume(): dec 0, phys_audio 0, level 0

[    5.055] AU [  49]|ICE_AudioVolume(): device_number 0, precent_volume 0

[  49]|board_hardware_standby(): seconds 86400
Pro moje oslovení klidně použijte jméno Zdeněk
Správně navržené zapojení je jako recept na dobré jídlo.
Můžete vynechat půlku ingrediencí, nebo přidat jiné,
ale jste si jistí, že vám to bude chutnat[?
]
Uživatelský avatar
rnbw
Příspěvky: 37418
Registrován: 21 bře 2006, 00:00
Bydliště: Bratislava

#27 Příspěvek od rnbw »

Takze procesor zije. A je tam zjavne Linux. Skusal si stlacit ENTER, ci sa dostanes do shellu?

Inak hlasenie "Image A is invalid marking it!" naznacuje, ze by mohol byt poskodeny firmware. Podla tych vypisov to vyzera tak, akoby tam bol dvakrat kvoli zalohe - "Image A" a "Image B".
Uživatelský avatar
ZdenekHQ
Významný člen
Příspěvky: 25519
Registrován: 21 črc 2006, 00:00
Bydliště: skoro Brno
Kontaktovat uživatele:

#28 Příspěvek od ZdenekHQ »

Já si taky myslím, že je může být poškozenej soft.

Komunikaci mám zatím zapojenou jednosměrně, navíc na ten stisk ENTER je pár set milisekund.

O aktualizaci softu přes PCMCIA jsem už na netu četl.

Ještě mě zajímá tady toto :

Kód: Vybrat vše

lock mutex timeout. errno[4] result[145] id[12] name[mxvs]
translate_vdev_error(): VDEV_DecodeStop(dec->eVideoCh): Mutex timeout [src/glue/src/glue_video.c:543 in glue_video_stop()]

lock mutex timeout. errno[4] result[145] id[12] name[mxvs]
translate_vdev_error(): VDEV_DecodeStop(dec->eVideoCh): Mutex timeout [src/glue/src/glue_video.c:543 in glue_video_stop()]
Pro moje oslovení klidně použijte jméno Zdeněk
Správně navržené zapojení je jako recept na dobré jídlo.
Můžete vynechat půlku ingrediencí, nebo přidat jiné,
ale jste si jistí, že vám to bude chutnat[?
]
Uživatelský avatar
rnbw
Příspěvky: 37418
Registrován: 21 bře 2006, 00:00
Bydliště: Bratislava

#29 Příspěvek od rnbw »

Ten enter podla mna pojde aj hocikedy potom, akurat na konzolu lezu rozne debug vypisy.
Tazko povedat, ci ta chyba je naozaj chyba, alebo je to normalne. Chcelo by to pozriet na inom kuse...
Uživatelský avatar
ZdenekHQ
Významný člen
Příspěvky: 25519
Registrován: 21 črc 2006, 00:00
Bydliště: skoro Brno
Kontaktovat uživatele:

#30 Příspěvek od ZdenekHQ »

Do shellu mě to pustí, ale musím odpojit komunikaci s okolím , jinak to vypne zdroj. Je to tam někde uprostřed včetně povolených příkazů.

Kód: Vybrat vše

 Checking for PCMCIA update...

  No card detected.

Booting mtd-block

Kernel located @ BFC00000

zimage at BFC10014

zimage size 0008CE4F

Uncompressing Linux at load address 80040000

Booting linux kernel @ 80159000
 Please press Enter to activate this console. Version out of Filesystem for Image A: 2 9
Version out of Filesystem for Image B: 2 9
Stored for Image A: ff 2 9
Stored for Image B: a5 2 9
Preferred Image: 1  Boot Fail Count A: 4  Boot Fail Count B:   2
Version numbers for Image A differ - updating Flash information



BusyBox v1.00 (2006.07.05-04:52+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

/ # Stored for Image A: a5 2 9
Image A is invalid marking it!


------------begin-of-log-------------

[    0.002] IN [  32]|audio_isr_bh(): woken up[a_dec 0] a_irq 0

[    0.002] IN [  32]|audio_isr_bh(): going to sleep[a_dec 0]

[    0.003] IN [  33]|audio_isr_bh(): woken up[a_dec 1] a_irq 0

[    0.003] IN [  33]|audio_isr_bh(): going to sleep[a_dec 1]

LNX_InitializeSystem() info:    System Initialize Start

Lnx_Open() debug:   open. device[/dev/tc90400int1]

Lnx_Open() debug:   open. device[/dev/tc90400int2]

Lnx_Open() debug:   open. device[/dev/tc90400int3]

Lnx_Open() debug:   open. device[/dev/tc90400int4]

Lnx_Open() debug:   open. device[/dev/tc90400int5]

lnx_mmap() info:    offset 0x00001000, size 0x01fff000, hint 0x40001000 =» map 0x40001000

lnx_mmap() info:    offset 0x17400000, size 0x00140000, hint 0x57400000 =» map 0x57400000

lnx_mmap() info:    offset 0x18000000, size 0x00090000, hint 0x58000000 =» map 0x58000000

lnx_mmap() info:    offset 0x180a0000, size 0x00020000, hint 0x580a0000 =» map 0x580a0000

lnx_mmap() info:    offset 0x180d0000, size 0x00330000, hint 0x580d0000 =» map 0x580d0000

lnx_mmap() info:    offset 0x1c004000, size 0x00001000, hint 0x5c004000 =» map 0x5c004000

lnx_mmap() info:    offset 0x1f100000, size 0x00010000, hint 0x5f100000 =» map 0x5f100000

lnx_mmap() info:    offset 0x1e01c000, size 0x00004000, hint 0x5e01c000 =» map 0x5e01c000

lnx_mmap() info:    offset 0x1e008000, size 0x00001000, hint 0x5e008000 =» map 0x5e008000

lnx_mmap() info:    offset 0x1e020000, size 0x00001000, hint 0x5e020000 =» map 0x5e020000

LNX_InitializeSystem() info:    System Initialize Start Done

0xa08b1000, 0x0018f000, TSPASP_FW

0xa0a40000, 0x00003000, IRISC_FW

0xa0a43000, 0x0000c000, WORK_AREA

0xa0a4f000, 0x00004000, COM_AREA

0xa0a53000, 0x00001000, AUDIO_WORK_AREA

0xa0a54000, 0x00134000, AUDIO_RES_AREA

0xa0bba000, 0x00020000, ASTD0

0xa0b88000, 0x00032000, AUDIO_DEC0

0xa0c1f000, 0x00080000, VSTD0

0xa0c9f000, 0x002f8000, VSTD1

0xa0c9f000, 0x002f8000, VBUF0

0xa0c9f000, 0x002f8000, VBUF1

0xa0c9f000, 0x002f8000, CAPTURE

0xa0c1e000, 0x00001000, VUSERBUF0

0xa0c9f000, 0x002f8000, VUSERBUF1

0xa0bda000, 0x0003c000, SECTIONS

0xa0c16000, 0x00008000, TPDATA

0xa0c9f000, 0x002f8000, RECORDING0

0xa0c9f000, 0x002f8000, RECORDING1

0xa0c9f000, 0x002f8000, PLAYBACK

0xa0f97000, 0x00065400, GFX_FB

0xa0ffd000, 0x00001000, GFX_SCALER

0xa0ffe000, 0x00001000, GFX_GFX_CLUT

0xa0fff000, 0x00001000, GFX_OSD_CLUT

0xa0c9f000, 0x002f8000, ASTD1

0xa0c9f000, 0x002f8000, AUDIO_DEC1

0xa0c9f000, 0x002f8000, ASTD2

0xa0c9f000, 0x002f8000, AUDIO_DEC2

0xa0c9f000, 0x002f8000, AUDIO_PCM0

0xa0c9f000, 0x002f8000, AUDIO_PCM1

0xa0c9f000, 0x002f8000, AUDIO_PCM2

0xa0c9f000, 0x002f8000, AUDIO_PCM3

__calc_memory_map(): mem 8820, lower map adr 8900

system_init(): debug 3, SD system

system_boot_MeP(): tspasp_fw @ 0xa08b1000

system_boot_MeP(): com_area  @ 0xa0a4f000

system_boot_MeP(): work_area @ 0xa0a43000

mutex object created. id[0] name[CmdFifoAccess]
mutex object created. id[1] name[TSPIntMaskRegAccess]
mutex object created. id[2] name[AMePIntMaskRegAccess]
mutex object created. id[3] name[STCIntMaskRegAccess]
mutex object created. id[4] name[TSPAudioStartStopRegAccess]
mutex object created. id[5] name[TSPASTDRunCh0RegAccess]
mutex object created. id[6] name[TSPASTDRunCh1RegAccess]
mutex object created. id[7] name[TSPASTDRunCh2RegAccess]
mutex object created. id[8] name[a0_mutex]
mutex object created. id[9] name[a1_mutex]
mutex object created. id[10] name[a2_mutex]
mutex object created. id[11] name[mxvd]
mutex object created. id[12] name[mxvs]
lock mutex timeout. errno[4] result[145] id[12] name[mxvs]
translate_vdev_error(): VDEV_DecodeStop(dec->eVideoCh): Mutex timeout [src/glue/src/glue_video.c:543 in glue_video_stop()]

lock mutex timeout. errno[4] result[145] id[12] name[mxvs]
translate_vdev_error(): VDEV_DecodeStop(dec->eVideoCh): Mutex timeout [src/glue/src/glue_video.c:543 in glue_video_stop()]

mutex object created. id[13] name[mi_mutex]
mutex object created. id[14] name[pf_mutex]
mutex object created. id[15] name[sf_mutex]
mutex object created. id[16] name[rf_mutex]
mutex object created. id[17] name[psf_mutex]
mutex object created. id[18] name[DemuxMutex]
system_init(): TSP-MeP-FW version: 0xbe215300
TSP-MeP-FW Demux-part version: 0x06122100
TSP-MeP-FW Video-part version: 0x07011600
TSP-MeP-FW DCXO-part version: 0x06031400

system_init(): IRISC-MEPG2-FW version: 0x00000000
IRISC-MPEG1-FW version: 0x00000000
IRISC-JPEG-FW version: 0x00000000
ASP-FW version: 0x07011700
AMP-FW version: 0x07011700

LNX_SetInterruptHandler() debug:   == set interrupt handler intno(0) ==

LNX_EnableInterrupt() debug:   GMBR interrupt enable.

LNX_SetInterruptHandler() debug:   == set interrupt handler intno(1) ==

LNX_EnableInterrupt() debug:   GFX  interrupt enable.

mutex object created. id[19] name[mxvd]
mutex object created. id[20] name[mxgd]
mutex object created. id[21] name[mxgs]
mutex object created. id[22] name[mxgm]
mutex object created. id[23] name[mxgb]
LNX_SetInterruptHandler() debug:   == set interrupt handler intno(2) ==

LNX_EnableInterrupt() debug:   VIOU interrupt enable .

LNX_SetInterruptHandler() debug:   == set interrupt handler intno(4) ==

LNX_EnableInterrupt() debug:   EXT1 interrupt enable .
 Checking for PCMCIA update...

  No card detected.

Booting mtd-block

Kernel located @ BFC00000

zimage at BFC10014

zimage size 0008CE4F

Uncompressing Linux at load address 80040000

Booting linux kernel @ 80159000
 Please press Enter to activate this console. Version out of Filesystem for Image A: 2 9
Version out of Filesystem for Image B: 2 9
Stored for Image A: ff 2 9
Stored for Image B: a5 2 9
Preferred Image: 1  Boot Fail Count A: 4  Boot Fail Count B:   3
Version numbers for Image A differ - updating Flash information
Stored for Image A: a5 2 9
Image A is invalid marking it!


------------begin-of-log-------------

[    0.002] IN [  32]|audio_isr_bh(): woken up[a_dec 0] a_irq 0

[    0.002] IN [  32]|audio_isr_bh(): going to sleep[a_dec 0]

[    0.003] IN [  33]|audio_isr_bh(): woken up[a_dec 1] a_irq 0

[    0.003] IN [  33]|audio_isr_bh(): going to sleep[a_dec 1]

LNX_InitializeSystem() info:    System Initialize Start

Lnx_Open() debug:   open. device[/dev/tc90400int1]

Lnx_Open() debug:   open. device[/dev/tc90400int2]

Lnx_Open() debug:   open. device[/dev/tc90400int3]

Lnx_Open() debug:   open. device[/dev/tc90400int4]

Lnx_Open() debug:   open. device[/dev/tc90400int5]

lnx_mmap() info:    offset 0x00001000, size 0x01fff000, hint 0x40001000 =» map 0x40001000

lnx_mmap() info:    offset 0x17400000, size 0x00140000, hint 0x57400000 =» map 0x57400000

lnx_mmap() info:    offset 0x18000000, size 0x00090000, hint 0x58000000 =» map 0x58000000

lnx_mmap() info:    offset 0x180a0000, size 0x00020000, hint 0x580a0000 =» map 0x580a0000

lnx_mmap() info:    offset 0x180d0000, size 0x00330000, hint 0x580d0000 =» map 0x580d0000

lnx_mmap() info:    offset 0x1c004000, size 0x00001000, hint 0x5c004000 =» map 0x5c004000

lnx_mmap() info:    offset 0x1f100000, size 0x00010000, hint 0x5f100000 =» map 0x5f100000

lnx_mmap() info:    offset 0x1e01c000, size 0x00004000, hint 0x5e01c000 =» map 0x5e01c000

lnx_mmap() info:    offset 0x1e008000, size 0x00001000, hint 0x5e008000 =» map 0x5e008000

lnx_mmap() info:    offset 0x1e020000, size 0x00001000, hint 0x5e020000 =» map 0x5e020000

LNX_InitializeSystem() info:    System Initialize Start Done

0xa08b1000, 0x0018f000, TSPASP_FW

0xa0a40000, 0x00003000, IRISC_FW

0xa0a43000, 0x0000c000, WORK_AREA

0xa0a4f000, 0x00004000, COM_AREA

0xa0a53000, 0x00001000, AUDIO_WORK_AREA

0xa0a54000, 0x00134000, AUDIO_RES_AREA

0xa0bba000, 0x00020000, ASTD0

0xa0b88000, 0x00032000, AUDIO_DEC0

0xa0c1f000, 0x00080000, VSTD0

0xa0c9f000, 0x002f8000, VSTD1

0xa0c9f000, 0x002f8000, VBUF0

0xa0c9f000, 0x002f8000, VBUF1

0xa0c9f000, 0x002f8000, CAPTURE

0xa0c1e000, 0x00001000, VUSERBUF0

0xa0c9f000, 0x002f8000, VUSERBUF1

0xa0bda000, 0x0003c000, SECTIONS

0xa0c16000, 0x00008000, TPDATA

0xa0c9f000, 0x002f8000, RECORDING0

0xa0c9f000, 0x002f8000, RECORDING1

0xa0c9f000, 0x002f8000, PLAYBACK

0xa0f97000, 0x00065400, GFX_FB

0xa0ffd000, 0x00001000, GFX_SCALER

0xa0ffe000, 0x00001000, GFX_GFX_CLUT

0xa0fff000, 0x00001000, GFX_OSD_CLUT

0xa0c9f000, 0x002f8000, ASTD1

0xa0c9f000, 0x002f8000, AUDIO_DEC1

0xa0c9f000, 0x002f8000, ASTD2

0xa0c9f000, 0x002f8000, AUDIO_DEC2

0xa0c9f000, 0x002f8000, AUDIO_PCM0

0xa0c9f000, 0x002f8000, AUDIO_PCM1

0xa0c9f000, 0x002f8000, AUDIO_PCM2

0xa0c9f000, 0x002f8000, AUDIO_PCM3

__calc_memory_map(): mem 8820, lower map adr 8900

system_init(): debug 3, SD system

system_boot_MeP(): tspasp_fw @ 0xa08b1000

system_boot_MeP(): com_area  @ 0xa0a4f000

system_boot_MeP(): work_area @ 0xa0a43000

mutex object created. id[0] name[CmdFifoAccess]
mutex object created. id[1] name[TSPIntMaskRegAccess]
mutex object created. id[2] name[AMePIntMaskRegAccess]
mutex object created. id[3] name[STCIntMaskRegAccess]
mutex object created. id[4] name[TSPAudioStartStopRegAccess]
mutex object created. id[5] name[TSPASTDRunCh0RegAccess]
mutex object created. id[6] name[TSPASTDRunCh1RegAccess]
mutex object created. id[7] name[TSPASTDRunCh2RegAccess]
mutex object created. id[8] name[a0_mutex]
mutex object created. id[9] name[a1_mutex]
mutex object created. id[10] name[a2_mutex]
mutex object created. id[11] name[mxvd]
mutex object created. id[12] name[mxvs]
lock mutex timeout. errno[4] result[145] id[12] name[mxvs]
translate_vdev_error(): VDEV_DecodeStop(dec->eVideoCh): Mutex timeout [src/glue/src/glue_video.c:543 in glue_video_stop()]

lock mutex timeout. errno[4] result[145] id[12] name[mxvs]
translate_vdev_error(): VDEV_DecodeStop(dec->eVideoCh): Mutex timeout [src/glue/src/glue_video.c:543 in glue_video_stop()]

mutex object created. id[13] name[mi_mutex]
mutex object created. id[14] name[pf_mutex]
mutex object created. id[15] name[sf_mutex]
mutex object created. id[16] name[rf_mutex]
mutex object created. id[17] name[psf_mutex]
mutex object created. id[18] name[DemuxMutex]
system_init(): TSP-MeP-FW version: 0xbe215300
TSP-MeP-FW Demux-part version: 0x06122100
TSP-MeP-FW Video-part version: 0x07011600
TSP-MeP-FW DCXO-part version: 0x06031400

system_init(): IRISC-MEPG2-FW version: 0x00000000
IRISC-MPEG1-FW version: 0x00000000
IRISC-JPEG-FW version: 0x00000000
ASP-FW version: 0x07011700
AMP-FW version: 0x07011700

LNX_SetInterruptHandler() debug:   == set interrupt handler intno(0) ==

LNX_EnableInterrupt() debug:   GMBR interrupt enable.

LNX_SetInterruptHandler() debug:   == set interrupt handler intno(1) ==

LNX_EnableInterrupt() debug:   GFX  interrupt enable.

mutex object created. id[19] name[mxvd]
mutex object created. id[20] name[mxgd]
mutex object created. id[21] name[mxgs]
mutex object created. id[22] name[mxgm]
mutex object created. id[23] name[mxgb]
LNX_SetInterruptHandler() debug:   == set interrupt handler intno(2) ==

LNX_EnableInterrupt() debug:   VIOU interrupt enable .

LNX_SetInterruptHandler() debug:   == set interrupt handler intno(4) ==

LNX_EnableInterrupt() debug:   EXT1 interrupt enable .



BusyBox v1.00 (2006.07.05-04:52+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

/ # help

Built-in commands:
-------------------
   . : break cd chdir continue eval exec exit export false hash
   help local pwd read readonly return set shift times trap true
   type ulimit umask unset wait

/ #   Checking for PCMCIA update...

  No card detected.

Booting mtd-block

Kernel located @ BFC00000

zimage at BFC10014

zimage size 0008CE4F

Uncompressing Linux at load address 80040000

Booting linux kernel @ 80159000
 Please press Enter to activate this console. Version out of Filesystem for Image A: 2 9
Version out of Filesystem for Image B: 2 9
Stored for Image A: ff 2 9
Stored for Image B: a5 2 9
Preferred Image: 1  Boot Fail Count A: 4  Boot Fail Count B:   4
Version numbers for Image A differ - updating Flash information



BusyBox v1.00 (2006.07.05-04:52+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

/ # Stored for Image A: a5 2 9
Image A is invalid marking it!
Image B is invalid marking it!
Image B not valid setting preffered Image to A
Service needed!


------------begin-of-log-------------

[    0.002] IN [  32]|audio_isr_bh(): woken up[a_dec 0] a_irq 0

[    0.002] IN [  32]|audio_isr_bh(): going to sleep[a_dec 0]

[    0.003] IN [  33]|audio_isr_bh(): woken up[a_dec 1] a_irq 0

[    0.003] IN [  33]|audio_isr_bh(): going to sleep[a_dec 1]

LNX_InitializeSystem() info:    System Initialize Start

Lnx_Open() debug:   open. device[/dev/tc90400int1]

Lnx_Open() debug:   open. device[/dev/tc90400int2]

Lnx_Open() debug:   open. device[/dev/tc90400int3]

Lnx_Open() debug:   open. device[/dev/tc90400int4]

Lnx_Open() debug:   open. device[/dev/tc90400int5]

lnx_mmap() info:    offset 0x00001000, size 0x01fff000, hint 0x40001000 =» map 0x40001000

lnx_mmap() info:    offset 0x17400000, size 0x00140000, hint 0x57400000 =» map 0x57400000

lnx_mmap() info:    offset 0x18000000, size 0x00090000, hint 0x58000000 =» map 0x58000000

lnx_mmap() info:    offset 0x180a0000, size 0x00020000, hint 0x580a0000 =» map 0x580a0000

lnx_mmap() info:    offset 0x180d0000, size 0x00330000, hint 0x580d0000 =» map 0x580d0000

lnx_mmap() info:    offset 0x1c004000, size 0x00001000, hint 0x5c004000 =» map 0x5c004000

lnx_mmap() info:    offset 0x1f100000, size 0x00010000, hint 0x5f100000 =» map 0x5f100000

lnx_mmap() info:    offset 0x1e01c000, size 0x00004000, hint 0x5e01c000 =» map 0x5e01c000

lnx_mmap() info:    offset 0x1e008000, size 0x00001000, hint 0x5e008000 =» map 0x5e008000

lnx_mmap() info:    offset 0x1e020000, size 0x00001000, hint 0x5e020000 =» map 0x5e020000

LNX_InitializeSystem() info:    System Initialize Start Done

0xa08b1000, 0x0018f000, TSPASP_FW

0xa0a40000, 0x00003000, IRISC_FW

0xa0a43000, 0x0000c000, WORK_AREA

0xa0a4f000, 0x00004000, COM_AREA

0xa0a53000, 0x00001000, AUDIO_WORK_AREA

0xa0a54000, 0x00134000, AUDIO_RES_AREA

0xa0bba000, 0x00020000, ASTD0

0xa0b88000, 0x00032000, AUDIO_DEC0

0xa0c1f000, 0x00080000, VSTD0

0xa0c9f000, 0x002f8000, VSTD1

0xa0c9f000, 0x002f8000, VBUF0

0xa0c9f000, 0x002f8000, VBUF1

0xa0c9f000, 0x002f8000, CAPTURE

0xa0c1e000, 0x00001000, VUSERBUF0

0xa0c9f000, 0x002f8000, VUSERBUF1

0xa0bda000, 0x0003c000, SECTIONS

0xa0c16000, 0x00008000, TPDATA

0xa0c9f000, 0x002f8000, RECORDING0

0xa0c9f000, 0x002f8000, RECORDING1

0xa0c9f000, 0x002f8000, PLAYBACK

0xa0f97000, 0x00065400, GFX_FB

0xa0ffd000, 0x00001000, GFX_SCALER

0xa0ffe000, 0x00001000, GFX_GFX_CLUT

0xa0fff000, 0x00001000, GFX_OSD_CLUT

0xa0c9f000, 0x002f8000, ASTD1

0xa0c9f000, 0x002f8000, AUDIO_DEC1

0xa0c9f000, 0x002f8000, ASTD2

0xa0c9f000, 0x002f8000, AUDIO_DEC2

0xa0c9f000, 0x002f8000, AUDIO_PCM0

0xa0c9f000, 0x002f8000, AUDIO_PCM1

0xa0c9f000, 0x002f8000, AUDIO_PCM2

0xa0c9f000, 0x002f8000, AUDIO_PCM3

__calc_memory_map(): mem 8820, lower map adr 8900

system_init(): debug 3, SD system

system_boot_MeP(): tspasp_fw @ 0xa08b1000

system_boot_MeP(): com_area  @ 0xa0a4f000

system_boot_MeP(): work_area @ 0xa0a43000

mutex object created. id[0] name[CmdFifoAccess]
mutex object created. id[1] name[TSPIntMaskRegAccess]
mutex object created. id[2] name[AMePIntMaskRegAccess]
mutex object created. id[3] name[STCIntMaskRegAccess]
mutex object created. id[4] name[TSPAudioStartStopRegAccess]
mutex object created. id[5] name[TSPASTDRunCh0RegAccess]
mutex object created. id[6] name[TSPASTDRunCh1RegAccess]
mutex object created. id[7] name[TSPASTDRunCh2RegAccess]
mutex object created. id[8] name[a0_mutex]
mutex object created. id[9] name[a1_mutex]
mutex object created. id[10] name[a2_mutex]
mutex object created. id[11] name[mxvd]
mutex object created. id[12] name[mxvs]
lock mutex timeout. errno[4] result[145] id[12] name[mxvs]
translate_vdev_error(): VDEV_DecodeStop(dec->eVideoCh): Mutex timeout [src/glue/src/glue_video.c:543 in glue_video_stop()]

lock mutex timeout. errno[4] result[145] id[12] name[mxvs]
translate_vdev_error(): VDEV_DecodeStop(dec->eVideoCh): Mutex timeout [src/glue/src/glue_video.c:543 in glue_video_stop()]

mutex object created. id[13] name[mi_mutex]
mutex object created. id[14] name[pf_mutex]
mutex object created. id[15] name[sf_mutex]
mutex object created. id[16] name[rf_mutex]
mutex object created. id[17] name[psf_mutex]
mutex object created. id[18] name[DemuxMutex]
system_init(): TSP-MeP-FW version: 0xbe215300
TSP-MeP-FW Demux-part version: 0x06122100
TSP-MeP-FW Video-part version: 0x07011600
TSP-MeP-FW DCXO-part version: 0x06031400

system_init(): IRISC-MEPG2-FW version: 0x00000000
IRISC-MPEG1-FW version: 0x00000000
IRISC-JPEG-FW version: 0x00000000
ASP-FW version: 0x07011700
AMP-FW version: 0x07011700

LNX_SetInterruptHandler() debug:   == set interrupt handler intno(0) ==

LNX_EnableInterrupt() debug:   GMBR interrupt enable.

LNX_SetInterruptHandler() debug:   == set interrupt handler intno(1) ==

LNX_EnableInterrupt() debug:   GFX  interrupt enable.

mutex object created. id[19] name[mxvd]
mutex object created. id[20] name[mxgd]
mutex object created. id[21] name[mxgs]
mutex object created. id[22] name[mxgm]
mutex object created. id[23] name[mxgb]
LNX_SetInterruptHandler() debug:   == set interrupt handler intno(2) ==

LNX_EnableInterrupt() debug:   VIOU interrupt enable .

LNX_SetInterruptHandler() debug:   == set interrupt handler intno(4) ==

LNX_EnableInterrupt() debug:   EXT1 interrupt enable .

mutex object created. id[24] name[TunerMutex]
mutex object created. id[25] name[TunerMutex]
[    2.785] MI [  30]|ICE_InitialiseSystemMemory(): not implemented

[    2.786] DE [  30]|ICE_DebugInit(): not implemented

[  30]|board_get_booted_image(): mtdblock 6, booted_image 0

[  30]|board_confirm_boot(): setting a bfc to 0

[  30]|write_store_value(): dest 7712, value 0x00, [0] 0x00, [1] 0xffffffff

[    2.789] DE [  30]|ICE_DebugInit(): not implemented

[    3.404] AU [  30]|ICE_AudioInit(): device_number 0

[    3.404] AU [  30]|ICE_AudioOpen(): device_number 0

[    3.407] ST [  30]|ICE_StcOpen(): [0]

[    3.444] CI [  30]|ICE_CIInit(): CI init

[    3.462] CI [  41]|ICE_CIResetAll(): Reset ALL Card

[    3.480] TP [  30]|ICE_TPDataInit():

[    3.480] TP [  30]|ICE_TPDataDeviceOpen(): [0x100579d0] device_type 0

[    3.485] TP [  30]|ICE_TPDataInit():

[    3.486] TP [  30]|ICE_TPDataDeviceOpen(): [0x100579d0] device_type 0

[  49]|board_get_booted_image(): mtdblock 6, booted_image 0

[    3.566] CI [  41]|ICE_CIOpen(): CI open slot:0

[    3.566] CI [  41]|ICE_CIOpen(): CI open slot:1

[  49]|read_version_information_from_flash(): image 0, major 2, minor 9

[  49]|board_get_image_version(): slot 0, valid 255, major 2, minor 9

[    3.575] BL [  49]|ICE_GetImageVersion(): image @ slot 0 invalid

[    3.575] SU [  49]|ICE_SoftwareVersion(): ICE_GetImageVersion() failed, boot_img 0

[  49]|read_version_information_from_flash(): image 0, major 2, minor 9

[  49]|board_get_image_version(): slot 0, valid 255, major 2, minor 9

[    3.596] BL [  49]|ICE_GetImageVersion(): image @ slot 0 invalid

[  49]|read_version_information_from_flash(): image 1, major 2, minor 9

[  49]|board_get_image_version(): slot 1, valid 255, major 2, minor 9

[    3.617] BL [  49]|ICE_GetImageVersion(): image @ slot 1 invalid

[  49]|read_store_value(): dest 7680, value 0x00

[  49]|board_get_preferred_image(): image 0

[    3.619] BL [  49]|ICE_GetBootSlot(): ICE_GetBootSlot 0

[    3.620] RE [  56]|board_receive_ir():

[    3.621] RE [  30]|ICE_RemoteRegisterKeypressFunction():

mutex object created. id[26] name[mxgd]
[  49]|board_get_fw_version(): now version : 2.2

[  49]|board_get_booted_image(): mtdblock 6, booted_image 0

[  49]|read_version_information_from_flash(): image 0, major 2, minor 9

[    4.366] IN [  49]|tee_stb_handler_audio_set_volume(): dec 0, phys_audio 0, level 1000

[    4.366] AU [  49]|ICE_AudioVolume(): device_number 0, precent_volume 100

[    4.480] RE [  49]|board_ir_set_repeat(): key 'ICE_keypress_volume_up'

[    4.481] RE [  49]|board_ir_set_repeat(): key 'ICE_keypress_volume_down'

[    4.481] RE [  49]|board_ir_set_repeat(): key 'ICE_keypress_program_up'

[    4.482] RE [  49]|board_ir_set_repeat(): key 'ICE_keypress_program_down'

[    4.974] IN [  49]|tee_stb_handler_audio_set_volume(): dec 0, phys_audio 0, level 0

[    4.975] AU [  49]|ICE_AudioVolume(): device_number 0, precent_volume 0

[  49]|board_hardware_standby(): seconds 86400
 Checking for PCMCIA update...

  No card detected.

Booting mtd-block

Kernel located @ BFC00000

zimage at BFC10014

zimage size 0008CE4F

Uncompressing Linux at load address 80040000

Booting linux kernel @ 80159000
 Please press Enter to activate this console. Version out of Filesystem for Image A: 2 9
Version out of Filesystem for Image B: 2 9
Stored for Image A: ff 2 9
Stored for Image B: ff 2 9
Preferred Image: 0  Boot Fail Count A: 0  Boot Fail Count B:   4
Version numbers for Image A differ - updating Flash information



BusyBox v1.00 (2006.07.05-04:52+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

/ # Stored for Image A: a5 2 9
Version numbers for Image B differ - updating Flash information
Stored for Image B: a5 2 9
Image B is invalid marking it!


------------begin-of-log-------------

[    0.002] IN [  32]|audio_isr_bh(): woken up[a_dec 0] a_irq 0

[    0.002] IN [  32]|audio_isr_bh(): going to sleep[a_dec 0]

[    0.003] IN [  33]|audio_isr_bh(): woken up[a_dec 1] a_irq 0

[    0.003] IN [  33]|audio_isr_bh(): going to sleep[a_dec 1]

LNX_InitializeSystem() info:    System Initialize Start

Lnx_Open() debug:   open. device[/dev/tc90400int1]

Lnx_Open() debug:   open. device[/dev/tc90400int2]

Lnx_Open() debug:   open. device[/dev/tc90400int3]

Lnx_Open() debug:   open. device[/dev/tc90400int4]

Lnx_Open() debug:   open. device[/dev/tc90400int5]

lnx_mmap() info:    offset 0x00001000, size 0x01fff000, hint 0x40001000 =» map 0x40001000

lnx_mmap() info:    offset 0x17400000, size 0x00140000, hint 0x57400000 =» map 0x57400000

lnx_mmap() info:    offset 0x18000000, size 0x00090000, hint 0x58000000 =» map 0x58000000

lnx_mmap() info:    offset 0x180a0000, size 0x00020000, hint 0x580a0000 =» map 0x580a0000

lnx_mmap() info:    offset 0x180d0000, size 0x00330000, hint 0x580d0000 =» map 0x580d0000

lnx_mmap() info:    offset 0x1c004000, size 0x00001000, hint 0x5c004000 =» map 0x5c004000

lnx_mmap() info:    offset 0x1f100000, size 0x00010000, hint 0x5f100000 =» map 0x5f100000

lnx_mmap() info:    offset 0x1e01c000, size 0x00004000, hint 0x5e01c000 =» map 0x5e01c000

lnx_mmap() info:    offset 0x1e008000, size 0x00001000, hint 0x5e008000 =» map 0x5e008000

lnx_mmap() info:    offset 0x1e020000, size 0x00001000, hint 0x5e020000 =» map 0x5e020000

LNX_InitializeSystem() info:    System Initialize Start Done

0xa08b1000, 0x0018f000, TSPASP_FW

0xa0a40000, 0x00003000, IRISC_FW

0xa0a43000, 0x0000c000, WORK_AREA

0xa0a4f000, 0x00004000, COM_AREA

0xa0a53000, 0x00001000, AUDIO_WORK_AREA

0xa0a54000, 0x00134000, AUDIO_RES_AREA

0xa0bba000, 0x00020000, ASTD0

0xa0b88000, 0x00032000, AUDIO_DEC0

0xa0c1f000, 0x00080000, VSTD0

0xa0c9f000, 0x002f8000, VSTD1

0xa0c9f000, 0x002f8000, VBUF0

0xa0c9f000, 0x002f8000, VBUF1

0xa0c9f000, 0x002f8000, CAPTURE

0xa0c1e000, 0x00001000, VUSERBUF0

0xa0c9f000, 0x002f8000, VUSERBUF1

0xa0bda000, 0x0003c000, SECTIONS

0xa0c16000, 0x00008000, TPDATA

0xa0c9f000, 0x002f8000, RECORDING0

0xa0c9f000, 0x002f8000, RECORDING1

0xa0c9f000, 0x002f8000, PLAYBACK

0xa0f97000, 0x00065400, GFX_FB

0xa0ffd000, 0x00001000, GFX_SCALER

0xa0ffe000, 0x00001000, GFX_GFX_CLUT

0xa0fff000, 0x00001000, GFX_OSD_CLUT

0xa0c9f000, 0x002f8000, ASTD1

0xa0c9f000, 0x002f8000, AUDIO_DEC1

0xa0c9f000, 0x002f8000, ASTD2

0xa0c9f000, 0x002f8000, AUDIO_DEC2

0xa0c9f000, 0x002f8000, AUDIO_PCM0

0xa0c9f000, 0x002f8000, AUDIO_PCM1

0xa0c9f000, 0x002f8000, AUDIO_PCM2

0xa0c9f000, 0x002f8000, AUDIO_PCM3

__calc_memory_map(): mem 8820, lower map adr 8900

system_init(): debug 3, SD system

system_boot_MeP(): tspasp_fw @ 0xa08b1000

system_boot_MeP(): com_area  @ 0xa0a4f000

system_boot_MeP(): work_area @ 0xa0a43000

mutex object created. id[0] name[CmdFifoAccess]
mutex object created. id[1] name[TSPIntMaskRegAccess]
mutex object created. id[2] name[AMePIntMaskRegAccess]
mutex object created. id[3] name[STCIntMaskRegAccess]
mutex object created. id[4] name[TSPAudioStartStopRegAccess]
mutex object created. id[5] name[TSPASTDRunCh0RegAccess]
mutex object created. id[6] name[TSPASTDRunCh1RegAccess]
mutex object created. id[7] name[TSPASTDRunCh2RegAccess]
mutex object created. id[8] name[a0_mutex]
mutex object created. id[9] name[a1_mutex]
mutex object created. id[10] name[a2_mutex]
mutex object created. id[11] name[mxvd]
mutex object created. id[12] name[mxvs]
lock mutex timeout. errno[4] result[145] id[12] name[mxvs]
translate_vdev_error(): VDEV_DecodeStop(dec->eVideoCh): Mutex timeout [src/glue/src/glue_video.c:543 in glue_video_stop()]

lock mutex timeout. errno[4] result[145] id[12] name[mxvs]
translate_vdev_error(): VDEV_DecodeStop(dec->eVideoCh): Mutex timeout [src/glue/src/glue_video.c:543 in glue_video_stop()]

mutex object created. id[13] name[mi_mutex]
mutex object created. id[14] name[pf_mutex]
mutex object created. id[15] name[sf_mutex]
mutex object created. id[16] name[rf_mutex]
mutex object created. id[17] name[psf_mutex]
mutex object created. id[18] name[DemuxMutex]
system_init(): TSP-MeP-FW version: 0xbe215300
TSP-MeP-FW Demux-part version: 0x06122100
TSP-MeP-FW Video-part version: 0x07011600
TSP-MeP-FW DCXO-part version: 0x06031400

system_init(): IRISC-MEPG2-FW version: 0x00000000
IRISC-MPEG1-FW version: 0x00000000
IRISC-JPEG-FW version: 0x00000000
ASP-FW version: 0x07011700
AMP-FW version: 0x07011700

LNX_SetInterruptHandler() debug:   == set interrupt handler intno(0) ==

LNX_EnableInterrupt() debug:   GMBR interrupt enable.

LNX_SetInterruptHandler() debug:   == set interrupt handler intno(1) ==

LNX_EnableInterrupt() debug:   GFX  interrupt enable.

mutex object created. id[19] name[mxvd]
mutex object created. id[20] name[mxgd]
mutex object created. id[21] name[mxgs]
mutex object created. id[22] name[mxgm]
mutex object created. id[23] name[mxgb]
LNX_SetInterruptHandler() debug:   == set interrupt handler intno(2) ==

LNX_EnableInterrupt() debug:   VIOU interrupt enable .

LNX_SetInterruptHandler() debug:   == set interrupt handler intno(4) ==

LNX_EnableInterrupt() debug:   EXT1 interrupt enable .

mutex object created. id[24] name[TunerMutex]
mutex object created. id[25] name[TunerMutex]
[    2.784] MI [  30]|ICE_InitialiseSystemMemory(): not implemented

[    2.785] DE [  30]|ICE_DebugInit(): not implemented

[  30]|board_get_booted_image(): mtdblock 6, booted_image 0

[  30]|board_confirm_boot(): setting a bfc to 0

[  30]|write_store_value(): dest 7712, value 0x00, [0] 0x00, [1] 0xffffffff

[    2.788] DE [  30]|ICE_DebugInit(): not implemented

[    3.404] AU [  30]|ICE_AudioInit(): device_number 0

[    3.405] AU [  30]|ICE_AudioOpen(): device_number 0

[    3.408] ST [  30]|ICE_StcOpen(): [0]

[    3.444] CI [  30]|ICE_CIInit(): CI init

[    3.463] CI [  41]|ICE_CIResetAll(): Reset ALL Card

[    3.480] TP [  30]|ICE_TPDataInit():

[    3.480] TP [  30]|ICE_TPDataDeviceOpen(): [0x100579d0] device_type 0

[    3.486] TP [  30]|ICE_TPDataInit():

[    3.486] TP [  30]|ICE_TPDataDeviceOpen(): [0x100579d0] device_type 0

[  49]|board_get_booted_image(): mtdblock 6, booted_image 0

[    3.566] CI [  41]|ICE_CIOpen(): CI open slot:0

[    3.566] CI [  41]|ICE_CIOpen(): CI open slot:1

[  49]|read_version_information_from_flash(): image 0, major 2, minor 9

[  49]|board_get_image_version(): slot 0, valid 165, major 2, minor 9

[    3.575] BL [  49]|ICE_GetImageVersion(): image @ slot 0 ok, major 2, minor 9

[    3.575] SU [  49]|ICE_SoftwareVersion(): sw_ver 29

[  49]|read_version_information_from_flash(): image 0, major 2, minor 9

[  49]|board_get_image_version(): slot 0, valid 165, major 2, minor 9

[    3.596] BL [  49]|ICE_GetImageVersion(): image @ slot 0 ok, major 2, minor 9
first slot version = 29

[  49]|read_version_information_from_flash(): image 1, major 2, minor 9

[  49]|board_get_image_version(): slot 1, valid 255, major 2, minor 9

[    3.617] BL [  49]|ICE_GetImageVersion(): image @ slot 1 invalid

[  49]|read_store_value(): dest 7680, value 0x00

[  49]|board_get_preferred_image(): image 0

[    3.619] BL [  49]|ICE_GetBootSlot(): ICE_GetBootSlot 0

[  49]|read_version_information_from_flash(): image 0, major 2, minor 9

[  49]|board_get_image_version(): slot 0, valid 165, major 2, minor 9

[    3.639] BL [  49]|ICE_GetImageVersion(): image @ slot 0 ok, major 2, minor 9
first slot version = 29

[  49]|read_version_information_from_flash(): image 1, major 2, minor 9

[  49]|board_get_image_version(): slot 1, valid 255, major 2, minor 9

[    3.660] BL [  49]|ICE_GetImageVersion(): image @ slot 1 invalid

[    3.660] BL [  49]|ICE_SetBootSlot(): ICE_SetBootSlot 0

[  49]|board_update_preferred_image(): preferred_image 0

[  49]|write_store_value(): dest 7680, value 0x00, [0] 0x00, [1] 0xffffffff

[    3.663] RE [  56]|board_receive_ir():

[    3.664] RE [  30]|ICE_RemoteRegisterKeypressFunction():

mutex object created. id[26] name[mxgd]
[  49]|board_get_fw_version(): now version : 2.2

[  49]|board_get_booted_image(): mtdblock 6, booted_image 0

[  49]|read_version_information_from_flash(): image 0, major 2, minor 9

[    4.404] IN [  49]|tee_stb_handler_audio_set_volume(): dec 0, phys_audio 0, level 1000

[    4.404] AU [  49]|ICE_AudioVolume(): device_number 0, precent_volume 100

[    4.518] RE [  49]|board_ir_set_repeat(): key 'ICE_keypress_volume_up'

[    4.519] RE [  49]|board_ir_set_repeat(): key 'ICE_keypress_volume_down'

[    4.519] RE [  49]|board_ir_set_repeat(): key 'ICE_keypress_program_up'

[    4.520] RE [  49]|board_ir_set_repeat(): key 'ICE_keypress_program_down'

[    5.025] IN [  49]|tee_stb_handler_audio_set_volume(): dec 0, phys_audio 0, level 0

[    5.025] AU [  49]|ICE_AudioVolume(): device_number 0, precent_volume 0

[  49]|board_hardware_standby(): seconds 86400

Pro moje oslovení klidně použijte jméno Zdeněk
Správně navržené zapojení je jako recept na dobré jídlo.
Můžete vynechat půlku ingrediencí, nebo přidat jiné,
ale jste si jistí, že vám to bude chutnat[?
]
Odpovědět

Zpět na „Servis televizorů, monitorů a projektorů - PROFI sekce“